QuiPlans
← All articles How to Read a Property Survey for ADU Planning how-to

How to Read a Property Survey for ADU Planning

Last Updated: November 7, 2026

Quick Summary

A property survey is a scaled drawing prepared by a licensed land surveyor that shows your lot's legal boundaries, structures, and recorded encumbrances. Read the title block first, then the legend, then trace each boundary line by its bearing and distance. Apply your zoning setbacks to the surveyed lot lines to find your buildable envelope.

  • Check the survey date before anything else, since an old plat may miss a fence, shed, or addition built since.
  • A bearing such as N 45° E gives direction and the distance that follows gives the length of one lot line.
  • Subtract setbacks, easements, and rights-of-way from the lot to find the buildable envelope for an ADU.
  • On a 6,000-square-foot example lot, a 600-square-foot ADU fits a 40-by-50-foot rear envelope with room to spare.
  • Confirm your plat is a boundary survey or better, not a sketch from a closing packet.
Can your lot fit an ADU?QuiPlans turns your survey into permit-ready ADU plans with PE-stamped drawings.
Browse ADU Plans

Table of Contents

Start With the Title Block and Survey Details

A property survey is a scaled drawing that shows your lot's legal boundaries, structures, and recorded encumbrances, prepared by a licensed land surveyor.

Learning how to read a property survey for ADU work starts in the title block. That corner block holds the facts you will use in every later step.

Read these fields first:

  • Surveyor name and license number. Confirms who prepared the plat and their authority to do so.
  • Survey date. Tells you how current the drawing is.
  • Legal description and lot number. Must match your deed.
  • Scale. The ratio that converts paper inches to real ground distance.
  • North arrow. Shows orientation, so you know which way the lot faces.

Check the date before anything else. An old survey may not show a fence, shed, or addition built since.

Decode Property Survey Symbols and Abbreviations

Property survey symbols and abbreviations are the shorthand a surveyor uses to mark boundaries, utilities, and improvements on the plat. A legend, usually printed on the sheet, translates each one. Find it before you read the drawing itself.

Land surveyor and homeowner reviewing a detailed property survey plat on a residential lot during the afternoon.
Land surveyor and homeowner reviewing a detailed property survey plat on a residential lot during the afternoon.

Common marks you will meet:

  • Solid line. Usually a boundary line or lot line.
  • Dashed line. Often an easement or right-of-way edge.
  • "IP" or a small circle. An iron pin or survey marker at a property corner.
  • "E" or "ESMT." An easement.
  • "R/W." Right-of-way.
  • "Bldg." Building footprint.

Watch out: symbols vary between surveyors. Never assume a mark means the same thing on two different plats. Always read the legend on the sheet in front of you.

How to Read a Survey Plat With Bearings and Distances

How to read a survey plat with bearings comes down to two numbers on each boundary line: a bearing and a distance. The bearing gives direction. The distance gives length.

A bearing looks like N 45° E. That means the line runs northeast, measured as an angle from north. A distance follows it, such as 100.00 feet.

Together they describe one lot line. Read each line around the perimeter and you can trace your full boundary.

A few practical notes:

  • Bearings are measured from north or south, toward east or west.
  • Distances are usually in feet and hundredths.
  • The scale converts the drawing to ground distance. A 1"=20' scale means one inch equals 20 feet.

If the numbers confuse you, the legal description in your deed repeats the same bearings and distances in words.

Find Your Boundaries, Setbacks, and Buildable Envelope

Your buildable envelope is the area left after setbacks are subtracted from your lot.

Here is the sequence:

  1. Trace the property boundary and lot lines on the plat.
  2. Mark the building footprint and any existing structures.
  3. Pull the required ADU setbacks from your zoning office.
  4. Measure inward from each lot line by the setback distance.
  5. Subtract easements and rights-of-way that overlap the remaining area.
  6. The leftover area is your buildable envelope.

Step 3 is where the survey stops and the code begins.

Three zoning numbers do most of the work:

  • Setbacks. Front, rear, and side yard minimums, often different for an ADU than for the main house. Confirm the setback figures for your zone with the local zoning office.
  • Lot coverage. The maximum percentage of your lot that can be covered by buildings, including the ADU footprint. If your house already covers 35 percent and the cap is 40 percent, a 600-square-foot ADU may not fit even if the setbacks allow it.
  • Height limit. The maximum height for an ADU, measured to the peak of the roof or to a mean height, depending on the code. A two-story design can fail a height limit that a single-story design passes.

A worked example shows how the numbers interact. Suppose the plat shows a 50-foot-wide by 120-foot-deep lot, or 6,000 square feet. The house footprint is 30 by 40 feet, or 1,200 square feet, and sits 20 feet from the front line and 10 feet from each side line. The rear yard is open. If the zoning code requires a 20-foot rear setback, a 5-foot side setback, and caps lot coverage at 40 percent, the math looks like this:

  • Maximum covered area at 40 percent is 2,400 square feet. The house already uses 1,200, leaving 1,200 square feet of coverage for the ADU and any other structures.
  • The open rear yard is 50 feet wide by 50 feet deep after the 20-foot rear setback, minus the 5-foot side setbacks on each side, leaving a 40-foot-wide by 50-foot-deep envelope.
  • A 600-square-foot ADU at 20 by 30 feet fits inside that envelope with room to spare, and it uses half of the remaining coverage allowance.

Change one number and the answer flips. Raise the rear setback to 30 feet and the envelope shrinks to 40 by 40 feet, still workable.

Watch out: a survey alone does not confirm code compliance. Confirm the actual ADU setback, coverage, and height requirements for your property before you draw anything, since they vary by zone and can change. How to Verify ADU Setback Requirements Before You Build walks through that check.

The worked example in the article shows how the key zoning numbers interact on a 6,000-square-foot lot.

Item Value Note
Lot size 50 by 120 feet, 6,000 sq ft Example lot from the plat
House footprint 30 by 40 feet, 1,200 sq ft Sits 20 ft from front, 10 ft from each side
Lot coverage cap 40 percent Maximum covered area is 2,400 sq ft
Coverage left for ADU 1,200 sq ft After subtracting the existing house
Rear setback 20 feet Leaves a 40-by-50-foot envelope
Side setbacks 5 feet each Applied to the open rear yard
Example ADU 600 sq ft at 20 by 30 feet Fits with room to spare
Raised rear setback 30 feet Envelope shrinks to 40 by 40 feet, still workable

Identify Easements, Rights-of-Way, and Encroachments

An easement is a legal right for someone else to use part of your land, such as a utility line or access path (easement | Wex | US Law). A right-of-way is a corridor reserved for access, often a public street or driveway.

All three affect where an ADU can go.

  • Utility easements. You usually cannot build over them.
  • Access easements. May limit placement near a shared driveway.
  • Encroachments. A neighbor's fence or shed on your lot can complicate permitting.

If you spot an easement on the plat, confirm whether it affects your build before you commit to a design. Our guide on how to verify if your property has ADU easements walks through that check.

How to Read a Property Survey PDF Without Missing Details

A property survey PDF hides details a paper print makes obvious. Zoom in, and read the sheet in a set order so nothing slips past you.

Follow this routine:

  • Open the PDF and zoom to the title block first.
  • Read the legend in full before the drawing.
  • Trace the boundary once without stopping.
  • Then re-read each lot line, checking bearings and distances.
  • Look for dashed lines that mark easements.
  • Check the north arrow and scale last.

Watch out: a low-resolution scan can blur small text. If the license number or a distance is unreadable, ask for a clearer copy from the surveyor or your title company.

Why You Need a Land Survey Before Building an ADU

A land survey before building an ADU gives you the boundary, setback, and easement facts a designer and permit office will ask for. Confirming boundaries and easements before design also helps prevent encroachment, an important part of protecting land investments.

But not every survey is good enough for ADU work. Before you rely on one, check three things: its age, its purpose, and whether it matches what you see on the ground.

Purpose. Surveys are prepared for different reasons. A boundary survey establishes lot lines and corners.

Accuracy and corners. Look for the surveyor's statement of accuracy and the monumentation shown at each corner.

When the survey conflicts with what you see on site, do not assume the plat is wrong or the fence is right. Follow this escalation path:

  1. Verify the document. Confirm you are reading the most recent survey and that the legal description matches your deed. A prior owner's survey may describe a different lot configuration.
  2. Compare against public records. Pull the recorded plat and your deed from the county recorder and compare bearings, distances, and lot numbers. A mismatch between the survey and the recorded documents is a surveyor question, not a homeowner question.
  3. Contact the surveyor. Ask the licensed surveyor who prepared the plat to review the discrepancy. Most will explain what they found and whether a field check is warranted.
  4. Do not build on an assumption. If a neighbor's fence appears to cross your line, or a shed sits where the plat shows open yard, resolve it before design. Encroachments can surface during permitting or at resale.

If your lot is tight or oddly shaped, a feasibility study ties the survey data to what will actually fit. Our walkthrough on an ADU feasibility study for tight lots shows how survey details feed that decision.

Order Permit-Ready ADU Plans That Match Your Survey

Once you can read the survey, you can order plans that fit your lot. The goal is a design that matches your boundary, setbacks, and buildable envelope from the start.

At QuiPlans, we provide permit-ready ADU floor plans and PE-stamped drawings from licensed structural engineers across 26 U.S. states.

Before you order, know what the package contains. Our guide on what is included in a permit-ready engineering package explains each drawing. When you are ready, you can browse permit-ready ADU plans built to match your surveyed lot.


Reading a survey correctly is the step most homeowners rush, and it is the one that decides whether an ADU fits.

Frequently Asked Questions

Can a property survey show whether an ADU will fit?

A property survey gives you the raw measurements you need, but it does not confirm an ADU will fit. You still have to apply local zoning rules for setbacks, lot coverage, and height to the boundary lines and buildable envelope shown on the plat. A survey also shows easements and existing structures that can shrink the usable area. Use the survey as your base map, then overlay the zoning envelope to see what is actually left to build on.

Do you need a new land survey before building an ADU?

Not always, but an old survey can cost you time. If the survey predates recent fences, additions, or lot splits, the boundary lines and building footprints may no longer match conditions on the ground. Many building departments want a current survey or site plan with permit applications. If your plat is more than a few years old or shows features that no longer exist, order an updated boundary survey before you finalize ADU plans.

What are red flags on a property survey for an ADU project?

Watch for easements cutting across the buildable area, encroachments where a fence or shed crosses the property line, and setbacks that leave too little room for the ADU footprint. A survey that conflicts with visible site conditions, such as a fence line that does not match the plat, is another warning sign. Any of these can force a redesign or a variance, so resolve them before you order final construction drawings.

How do you read a survey plat with bearings and distances?

Bearings are compass directions written as degrees, minutes, and seconds from north or south, such as N 45° 12' 30" E. Distances tell you how far each line runs in feet. Start at a marked property corner, follow each bearing and distance around the perimeter, and you will trace the boundary back to the starting point. The north arrow on the plat sets the orientation, so always check it before you interpret any bearing.

GoogleAdd quiplans.com as a preferred source on Google →