how-to
Submit Your Own Structural Drawings: Permit Rules
Last Updated: November 12, 2026
Quick Summary
Yes, in many jurisdictions a homeowner can submit their own structural drawings for a permit, but submission is not the same as design. The structural design behind those sheets often needs a licensed engineer, and many jurisdictions still require a licensed engineer or architect to design and seal the structural sheets even when the owner files the paperwork.
- Ask your building department two separate questions: may I submit as the owner, and who must prepare and seal the design?
- Some states limit owner-prepared plans to a single-family residence the owner will occupy.
- Building permit plans need an engineer stamp when the structural design falls under state licensing law.
- Many jurisdictions accept owner-submitted drawings through an online portal, but the portal does not change the design rules.
- Uploading a single flattened PDF with unlabeled sheets and no sheet index can lead to rejection at intake.
Table of Contents
- Can You Submit Your Own Structural Drawings for a Permit?
- Building Permit Drawing Requirements: What Belongs in the Set
- When Structural Work Requires a Licensed Engineer
- Do Building Permit Plans Need an Engineer Stamp?
- How to Make a Site Plan for Permit
- Can I Submit My Own Structural Drawings for Permit Online?
- Get PE-Stamped Drawings Ready for Your Submittal
- Frequently Asked Questions
Can You Submit Your Own Structural Drawings for a Permit?
Yes, in many jurisdictions a homeowner can submit their own structural drawings for a permit. See Owner Builder Plans on QuiPlans for the owner-builder path and resources for submitting plans without a contractor. But submission is not the same as design. The structural design behind those sheets often needs a licensed engineer.
That distinction decides your whole project.
Here is what matters most before you draw anything:
- Who may submit: often the owner, sometimes the contractor or a design professional.
- Who may design: varies by project scope and local rules.
- Who may seal: only a licensed engineer or architect, where a seal is required.
Below, we break down the drawing set, the engineer rules, and the online submittal path. International Code Council overview of the building code
Building Permit Drawing Requirements: What Belongs in the Set
A permit drawing set is the package of construction documents a building department reviews to confirm code compliance. Most residential sets include architectural sheets and, when structural work is involved, structural sheets.

A common mistake is sending a single floor plan and calling it a set. Inspectors want to see the whole picture.
Architectural Sheets: Site Plan, Floor Plan, Elevations, and Sections
These sheets show what the project looks like and where it sits. They typically cover:
- Site plan: property lines, setbacks, and the building footprint
- Floor plan: room layout, dimensions, and wall locations
- Elevations: exterior views from each side
- Building sections: a cut-through showing heights and assemblies
Structural Sheets: Foundation, Framing, and Connection Details
Structural sheets carry the load path.
- Foundation plan with footing sizes
- Framing plan for beams, joists, and headers
- Connection details for hardware and fasteners
- Member sizing and design loads
For a full breakdown, see what a permit-ready engineering package includes.
When Structural Work Requires a Licensed Engineer
Most building departments draw the line at anything that changes the load path, the route forces travel from the roof through the walls and foundation to the ground. Cosmetic work like cabinets, paint, or a new floor finish usually stays on the homeowner side of that line. Structural work usually does not.
Common triggers that bring a licensed engineer into a residential project include:
- Removing or altering a load-bearing wall, including widening a doorway in one.
- Adding a beam or header to open up a span, or replacing a post with a longer span.
- Foundation work, new footings, underpinning, slab replacement, or a basement dig-out.
- Second-story additions, dormers, and roof-line changes that add load to existing framing.
- Long spans or cantilevers beyond what prescriptive tables in the residential code cover.
- Unusual site conditions, expansive soils, steep slopes, flood zones, or high-wind and seismic design categories.
- Decks and porches above a certain height or attached to the house, where ledger and lateral-load connections matter.
A useful distinction: permission to submit plans is not permission to prepare or certify structural designs. Many jurisdictions let a homeowner file the paperwork while still requiring a licensed engineer or architect to design and seal the structural sheets. Ask your building department two separate questions, "May I submit as the owner?" and "Who must prepare and seal the structural design for this scope?", because the answers can differ.
Local rules control. Some states limit owner-prepared plans to a single-family residence the owner will occupy; others require a design professional for any structural alteration regardless of occupancy. Before you draw, call the permit counter or check the jurisdiction's homeowner-permit page and ask for the specific section of the adopted code that governs owner-prepared structural drawings. Get the answer in writing if you can.
Watch out: assuming a small beam swap is exempt because a neighbor did it without a stamp, the scope, span, and local amendment may differ.
Do Building Permit Plans Need an Engineer Stamp?
Building permit plans need an engineer stamp when the project involves structural design that falls under state licensing law. A professional seal is the engineer's signed statement that the design meets code. A professional seal is especially important when structural changes such as removing a load-bearing wall are involved, and Caledonian Customs can help frame the safety considerations that go with that work.
Not every set needs one. A deck replacement may not. A new addition usually does.
Your building department can confirm the requirement for your scope. Read what a PE stamp is and when it applies to check your situation.
How to Make a Site Plan for Permit
A site plan for permit is a scaled drawing showing your property lines, setbacks, and building footprint. Most departments want it at a stated drawing scale, with dimensions and a north arrow.
Follow these steps:
- Pull your property survey or plat map.
- Mark the property line and measured setbacks.
- Draw the existing and proposed structures.
- Add dimensions, easements, and the north arrow.
- Label the scale and address.
Keep it simple and accurate. Neat beats fancy.
Can I Submit My Own Structural Drawings for Permit Online?
Many jurisdictions accept owner-submitted drawings through an online portal, and the file format and portal rules vary by jurisdiction. The portal does not change the design rules, it only changes how the package reaches the reviewer. What gets plans bounced before review is almost always format, not engineering.
Submission-ready standards to confirm with your building department before you upload:
- Scale: structural and architectural sheets are typically drawn at a stated scale (commonly 1/4 inch = 1 foot for floor plans, 1/8 inch = 1 foot for site plans) and labeled on every sheet. Verify the required scale, some departments reject sheets marked "NTS" (not to scale).
- Sheet organization: a cover sheet with the project address, owner name, scope, and sheet index; then site, floor, elevation, section, structural, and detail sheets in a consistent order. Sheet numbers (S-1, S-2, A-1) should match the index.
- Dimensions and notes: every structural member should carry a size, spacing, and material callout, with general notes covering design loads and code edition.
- Signatures and seals: where a seal is required, the sheet needs the engineer's signature, seal, and date. Where the owner is submitting, some departments require an owner's affidavit or a signed statement that the owner prepared the plans.
- File format and naming: PDF is standard; check the size cap for each file, whether the portal wants one combined set or separate sheets, and whether it enforces a naming convention such as address-sheet number-revision.
After submission, plan review typically runs in stages, intake and completeness check, then technical review by plan reviewers (and often a separate structural reviewer). Comments come back as a correction notice or plan-revision request. You respond by uploading revised sheets with a revision cloud and a response letter that addresses each comment by number. Plan for the possibility of a correction cycle rather than treating the first upload as final.
Fees and timelines vary widely by jurisdiction and project valuation, so confirm the current fee schedule and published review times with your building department rather than relying on a general estimate.
Watch out: uploading a single flattened PDF with unlabeled sheets and no sheet index can lead to a submittal being rejected at intake.
Before you upload, confirm these submission-ready standards with your building department.
| Item | Value | Note |
|---|---|---|
| Floor plan scale | Commonly 1/4 inch = 1 foot | Labeled on every sheet |
| Site plan scale | Commonly 1/8 inch = 1 foot | Sheets marked NTS may be rejected |
| Sheet order | Cover, site, floor, elevation, section, structural, detail | Sheet numbers should match the index |
| Structural callouts | Size, spacing, and material for every member | General notes cover design loads and code edition |
| Seals | Engineer signature, seal, and date where required | Owner affidavit may be required |
| File format | PDF is standard | Check size cap and naming convention |
Get PE-Stamped Drawings Ready for Your Submittal
The safest route is to prepare the drawings correctly the first time. QuiPlans provides PE-stamped drawings from licensed structural engineers across 26 U.S. states.
Our permit-ready engineering services include PE-stamped drawings. We also offer feasibility studies and construction administration support.
Start your engineering intake and get drawings ready for submittal.
The real risk is not the paperwork. It is a correction cycle that stalls your project for weeks. Get the structural design right before you submit, and plan review becomes a formality. Get started with QuiPlans and submit a drawing set built for approval.
Frequently Asked Questions
Can I draw my own building plans and submit them for a permit?
In many jurisdictions, homeowners can prepare and submit their own drawings for a single-family residence they will occupy, provided the drawings meet building permit drawing requirements. The catch is structural work: if the project touches load-bearing walls, adds a second story, or changes the foundation, the building department usually requires structural calculations and a professional seal from a licensed engineer. Confirm your local rules before you draw, because the threshold varies by jurisdiction.
Do structural drawings need to be stamped by an engineer?
Not every sheet in a permit set needs a stamp, but structural drawings for anything beyond minor repairs typically do. Plans examiners look for a licensed engineer's professional seal and signature on the structural calculations, member sizing, and connection details. Simple projects such as a non-structural interior remodel may clear review without one. If your project involves a new foundation, beam replacement, or an addition, expect the building department to ask for a sealed set.
What happens if my permit drawings are rejected?
A rejection usually arrives as a correction notice listing specific deficiencies, such as missing dimensions, unclear setbacks, or structural calculations that do not show design loads. You can revise and resubmit, but each correction cycle adds review time. Drawings that are complete, drawn to a consistent scale, and paired with sealed structural sheets clear review faster. If the corrections involve structural questions, a licensed engineer can address them directly rather than you guessing at the fix.
Can I submit my own structural drawings for permit online?
Most building departments now accept electronic submission through an online portal, and the same plan review standards apply whether you submit digitally or at the counter. File format, sheet size, and naming rules vary by jurisdiction, so check the portal's drawing standards before uploading. Submitting online does not change who is allowed to prepare the drawings, so the engineer stamp question still applies. A submission-ready PDF set with a clear sheet index reduces back-and-forth during plan review.